Shop by Category
Shop by Brand
- Aaeon
- Accel Instruments
- Adlink
- Antaira
- Arbor
- Array
- Asian Electron
- Atek
- Atten
- Bravo Communications
- Diamond Systems
- Digilent -MCC
- Digi International
- Dino-Lite
- Dwyer
- Extech
- GW Instek
- Handywave
- ICS Electronics
- ITECH
- LabJack
- Jewell Instruments
- Juniper
- Lascar
- Micronor Sensors
- Motrona
- MSR
- Numato
- Omega
- Opto22
- ORing
- PowerVar
- Rigol
- Senonics
- Siglent
- Tripp Lite
- TVBTECH
- Twintex
- Vaisala
- Winmate
ORing Industrial 1-port Gigabit High Power PoE++ Injector (INJ-101GT++-60W-24)
$0.00
The INJ-101GT++ PoE Injector series is not only an IEEE802.3at compliant device but also an advanced high power PoE injector. It is intelligent detection that provided 1-ports 10/100/1000Base-T (X) PoE outputs.
The device does not turn on power until it detects a valid PoE signature from the PoE devices attached downstream on the Ethernet cable.
This protection against damage to non-PoE compliant equipment which may be connected to the Ethernet cable. Therefore, only an IEEE 802.3at/802.3af compliant device can be powered with the INJ-101GT++ PoE Injector.
Typically in Gigabit networks the maximum allowable CAT5 cable length is about 100 meters, due to the limitation of the Ethernet standards. The INJ-101GT++ PoE Injector can function with any PoE P.D. equipment which is fully compliant with the IEEE 802.3af/at PoE standards, and provide the DIP switch configurator for High power PoE management.
Features:
- PoE++ Injector for 1x10/100/1000Base-T(X)
- Fully compliant with IEEE802.3at/802.3af standard
- Auto protection for Over Voltage Power Input and over current output
- Supports totallyPower Output up to 60Watts for all ports usage.
- Support wide range power input, 9 to 57VDC
- Provided DIP switch configurator for PoE mode management
- High reliability and rigid IP-30 housing
- DIN-Rail and Wall Mount Design
Specifications:
| ORing Injector Model | INJ-101GT++-60W-24V |
| Physical Ports | |
| RJ-45 Ethernet Port Input | 1 |
| RJ-45 Ethernet Port with P.S.E. Output | 1 |
| Operating Voltage | |
| Input Voltage | 9 ~ 57 VDC on 4-pin terminal block |
| LED Indicators | |
| Power Indicator | PWR / Ready: 1 x LED Green On: Power is on and functioning Normally. |
| PoE Indicators | 1 x LED Blue On: PoE Device Link Off : None PoE Device Detected Blink (Blue) : Overload present |
| DIP Switch | |
| DIP Switch 1/2 |
DIP Switch 1/2 (OFF): PoE P.S.E set to master and Asyncronize mode DIP Switch 1/2 (ON) : PoE P.S.E set to syncronize mode(default) |
| Power | |
| Input Power | 9 ~ 57 VDC on 4-pin terminal block |
| Power Consumption | 1 Watts (Not include PD's device) |
| PoE Power Budget | 30Watt at 9~24VDC, 60Watt at 24~57VDC |
| Protection | |
| Short Circuit Protection | Present |
| Over Load Protection | Present |
| Physical Characteristics | |
| Enclosure | IP-30 |
| Dimensions (W x D x H) | 41(W)x70(D)x95(H)mm (1.03 x 2.76 x 3.74 inch) |
| Weight (g) | 318 g |
| Environmental | |
| Storage Temperature | -40 to 85°C (-40 to 185°F) |
| Operating Temperature | -40 to 75°C (-40 to 167°F) |
| Operating Humidity | 5% to 95% Non-condensing |
| Regulatory Approvals | |
| EMC | CE EMC (EN55024,EN 55032), FCC Part 15 B |
| EMI | EN55032, CISPR 32, EN61000-3-2, EN61000-3-3, FCC Part 15 B class A |
| EMS | EN55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT), IEC/EN61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8 (PFMF), IEC/EN 61000-4-11 (DIP) |
| Shock | IEC60068-2-27 |
| Free Fall | IEC60068-2-32 |
| Vibration | IEC60068-2-6 |
| Safety | EN60950-1 |
| MTBF | 2067004hrs |
| Warranty | 5 years |
*Note1: (1) By default, the output value of the high power PoE++ is in Sync mode which supports PoE af/at-compliant P.D. devices.
(2) If you cannot enable the 60W PTZ camera, please set the DIP switch to Async mode and reconnect power. This mode only supports Dual P.D mode. You may not connect to an af/at-compliant P.D. device with this mode.
